Contact Us
03333 441 399 (local rate even from mobiles)
Are you looking for a Bristol heating engineer for a Ferroli Boiler repair? We can help! Call 03333 441 399
Ferroli has been producing heating appliance design and development for more than 50 years and now operates in over 100 countries worldwide. The full range of their boilers are manufactured in Verona, Italy.
With every boiler, Ferroli manufactured boilers experience problems with constant use and when the winter season kicks in. Here at Plumbing Care Services we serve Bristol, Somerset & Gloucestershire for all Ferroli Boiler customers. Here is a list of fault codes and possible issues that may arise with these boilers.
Please note that we do not suggest that you try to rectify any faults listed as this may put your safety at risk, and also cause any warranties the boiler may have. The best thing to do is call us at Boiler Care Services for 24/7 emergency repairs.
Check for any leaks from the boilers pressure relief valve, or any of your homes radiators. If you can’t locate this, the problem is that it’s usually an issue with the expansion vessel which will need to be repressurised. This can only be repaired or re-set from a qualified engineer which is a quick fix. If this is not the fix required the boiler may need a replacement vessel.
This is a particular fault with this brand of boilers, as the shut valves tend to wear out. The only option is to have these replaced by a qualified engineer.
The boiler isn’t coming on at the correct time. This is highly likely to be a fault with the boilers timer. Thi is a simple and relatively cheap fix for any qualified engineer to complete.
If the boiler is producing a puffy sound of air then the problem is likely to be with the boilers flue. This can be from a number of reasons as the boiler gets more use down the years from flue duct corrosion of loose joints within the flue. If this is the case then an engineer is required to replace all the parts.
The printed circuit board is likely to be malfunctioned. This needs to be properly checked by an engineer to ensure that there is a supply of electricity reaching it. If this is the case, then a new PCB will need to be installed.
If your Ferroli boiler is showing an error code, here are some pointers for you. If the code on your Ferroli boiler is not listed, let us know when you call for your repair. Please note it’s always best to look at the owner’s manual for the full list for your specific model.
A01. No burner ignition – possible electrode error, defective gas valve or incorrect inlet gas pressure.
A02. Flame detected with the burner off.
A03. High limit protection.
A04. Flue gas fault.
A05. Fan error.
A06. No flame after the ignition phase.
A41. Flow sensor error – sensor disconnected.
A42. Flow sensor error – sensor damaged.
F07. High fume temperature.
F10. Flow sensor error.
F11. Return sensor error.
F13. Exchanger probe error.
F14. Flow sensor.
F15. Fan problem.
F34. Supply voltage under 170v – electric supply error.
F35. Irregular mains frequency – electric supply problem.
F37. Incorrect system water pressure error.
F43. Exchanger protection activation.
F52. Flow sensor.
A61. Controller ABM03B error – controller has an internal error.
A62. No communication between controller and gas valve.
A63 / A64 / F66. Controller ABM03B error.
A01. Ignition error – possible electrode fault or power too low, no gas or excessive condensate level.
A02. Electrode or card error.
A03. Heating sensor damaged, no water circulation or air in system.
F07. Air pressure switch error.
A09. Gas valve error.
F10. Delivery sensor error, sensor damaged wiring shorted or disconnected.
F11. Domestic hot water (DHW) sensor error.
A15. Fault F05 generated 5 times within the last 24 hours – possible error with the air pressure switch.
A16. Gas valve error.
A23. Card parameter error.
F34. Supply voltage under 170V – electric mains error.
F35. Faulty mains frequency. Electric mains error.
F37. Error with system water pressure.
A01. No burner ignition, No gas or ignition , issue with detection electrode, faulty gas valve or insufficient gas supply pressure.
A02. Flame signal present with burner off Electrode error or PCB error.
A05. Fan error No 230V power supply or tachometric signal interrupted fan damaged or out of balance.
A06. No flame after the ignition phase.
F07 – F14 – A07. High flue gas temperature.
F08 – A08. Overtemperature protection intervention Heating sensor damaged. No water circulation in the system or air in the system.
F09 – A09. Overtemperature protection intervention Return sensor damaged.
F10 – A10. Flow sensor error Sensor damaged.
F11 – A11. Return sensor fault Sensor damaged.
F12. DHW sensor error Sensor damaged.
F13 – A13. Flue probe fault Probe damaged.
A14. Flue extraction duct safety device intervention.
F34. Supply voltage under 170V Electric mains trouble.
F37. Incorrect system water pressure, pressure too low.
F39. Optional external probe error. Probe is damaged or wiring shorted.
A01. No burner ignition
A02. Flame detected with the burner off
A03. High limit protection
A04. Flue gas fault
A05. Fan problem
A06. No flame after ignition phase
A41. Flow sensor disconnected
A42. Flow sensor fault
F07. High fume temperature
F10. Flow sensor fault
F11. Return sensor fault
F12. Domestic hot water (DHW) sensor fault
F13. Exchange probe fault
F14. Fan problem
F15. Supply voltage under the required level
F34. Irregular mains frequency
F35. Incorrect system water pressure
F37. External probe fault sensor damaged or short circuited
F39. Exchanger protection activation – possibly caused by no system circulation, air in the system or sensor damaged
F4.3 Flow sensor fault
F52. Controller 041049G0 fault
A61. No communication between controller and gas valve controller
A62. Controller 041049G
A63 / A64 / F66. Controller DBM12 fault
Call 03333 441 399 or fill out our contact form.
To book a repair or your yearly maintenance service of your Biasi Gas Boiler in Bristol, Gloucestershire and Somerset, call the experts at Plumbing Care Services today at 03333 441 399. (Local rate even for mobiles)
We strive to provide a 60 minute response time to prevent any lasting damage being done to your property. Emergency plumbing repairs are our priority, so if we can get there, we will.
If you need an emergency plumber immediately, please call us now on 03333 441 399.
Thanks to our reputation as the top plumbing and central heating company in Bristol, Somerset & Gloucestershire, we’ve been given Approved Installer status from a variety of well-known names in the industry, including Worcester Bosch, Glow Worm, Baxi and Vaillant.
Call Now